HIGHSIDER NUMBER PLATE BRACKET PLATE HOLDER AKRON-RS 1108065

HIGHSIDER AKRON-RS license plate holder



The HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design.



The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting.

To prevent damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet.



The license plate is made of sheet steel and 2 mm thick. The precise cutting is done by laser. After edging, the weather-resistant black powder coating is applied.

This ensures the optimal fit and durability.

Through the stepless adjustment you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw.



The AKRON-RS turn signal brackets are adjustable in width and therefore suitable for any type of accessory turn signal. This adjustment option allows you to adapt the position for your turn signals to the most varied number plates. To allow mounting the turn signals without disconnecting them from the wiring harness, the 10 mm holes are slotted to the side.



You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of the EU license plates is therefore no problem.



To screw the license plate securely and reduce vibration, two rubber washers are included. Another rubber buffer supports the license plate on its underside.



Details:



- model-specific bracket

- infinitely adjustable turn signal holder

- slotted turn signal holder for easy mounting without cable separation

- infinitely adjustable reflector, E-approved

- suitable for European license plates

- infinitely adjustable tilt angle

- additional screw for optimum position security

- easy fixation without further work steps (e. g.B. Drilling)

- easy mounting of the license plate through slotted holes



The scope of delivery of the AKRON-RS includes:



- Model-specific bracket with mounting parts

- AKRON-RS license plate mounting plate

- Adjustable turn signal holders

- E-tested reflector with adjustable holder

- Mounting instructions



Note:

The special turn signal bracket 280-970 is optionally available for the original turn signals.



Tips:

If you have not found a model-specific license plate holder for your vehicle, then you will certainly find the universal license plate holders from HIGHSIDER, which are available in many different designs.
COLOR: NEGRO
COMPOSICIÓN: ALUMINIO


APPLICATIONS OF THIS PRODUCT:
According to the data provided by the manufacturer, this article is compatible with the following brands, models and years:
APRILIA RS4 125 125 2017
APRILIA RSV4 1100 ABS FACTORY 1100 2019-2021
APRILIA RSV4 ABS 1000 2009-2015
APRILIA RSV4 APRC 1000 2009-2016
APRILIA RSV4 FACTORY 1000 2009-2017
APRILIA RSV4 FACTORY ABS 1000 2009-2017
APRILIA RSV4 FACTORY APRC SE 1000 2009-2016
APRILIA RSV4 FW 1000 2017
APRILIA RSV4 R 1000 2009-2018
APRILIA RSV4 R ABS 1000 2009-2018
APRILIA RSV4 RF 1000 2015-2019
APRILIA RSV4 RR 1000 2015-2020
APRILIA TUONO 1000 1000 2011-2012
APRILIA TUONO 1000 FACTORY 1000 2011-2012
APRILIA TUONO 1000 R 1000 2011-2015
APRILIA TUONO 1000 R FACTORY 1000 2011
APRILIA TUONO 1000 RR 1000 2011
APRILIA TUONO 1000 V4 1000 2011-2015
APRILIA TUONO 1000 V4 R 1000 2011-2016
APRILIA TUONO 1000 V4 R ABS 1000 2012-2016
APRILIA TUONO 1000 V4 R APRC ABS 1000 2011-2016
APRILIA TUONO 1100 V4 FACTORY 1100 2016-2020
APRILIA TUONO 1100 V4 RR 1100 2015-2020
APRILIA TUONO 125 125 2017-2019